федеральное государственное автономное образовательное учреждение высшего образования
«Самарский национальный исследовательский университет имени академика С.П. Королева»

Demyanenko, Elena G.

  • Department of Metal Forming, specialist
  • leading researcher
2024
  • 1 Dem’yanenko E.G., Popov I.P., Nikonov D.A. Determination of the Area of Workpiece Destruction during the Deep Drawing into a Conical Die // Russian Aeronautics 2024. — Vol. 67. Issue 1. № 1. — P. 161-169
2023
  • 1 Dem’yanenko E.G., Levagina A.A. Improving the Molding Process to Obtain Thin-Walled Axisymmetric Parts of a Truncated Tapering Shape // Russian Aeronautics 2023. — Vol. 66. Issue 3. № 3. — P. 573-580
2022
  • 1 Demyanenko E.G., Popov I.P., Kuznetsov A.S. Modeling of the Heat Setting Process in Order to Eliminate Defects in the Obtained Part // Lecture Notes in Mechanical Engineering. — 2022. — P. 253-260
2021
  • 1 Popov I., Nikonov D., Demyanenko E. etc. ANSYS/LS-DYNA Simulation-Based Study of Buckling Caused Deep Drawing Limiting Parameters // 2021 International Scientific and Technical Engine Conference (EC). — 2021. — P. 1-4
  • 2 Demyanenko E.G., Popov I.P., Kosolapova A.Yu. Study of the process of forming large-sized thin-walled parts // II International Scientific and Practical Conference: Materials Science, Engineering and Energy: Problems and Prospects of Development (MSEE 2020) . — 2021. — Vol. 1100.
2020
  • 1 Demyanenko E.G., Popov I.P. Investigation into the flanging process with minimal thickness variation // Materials Science Forum. — 2020. — Vol. 989 MSF. — P. 636-641
2019
  • 1 Demyanenko E.G., Epifanov A. N. , Popov I.P. Simulation of the combined flanging and forming process taking into account the springback effect // Journal of Physics: Conference Series. — 2019. — Vol. 1368. Issue 4.
  • 2 Dem’yanenko E.G. Investigation of the Forming Process of Thin-Walled Parts from a Flat Blank with Minimal Thickness Variation // Russian Aeronautics 2019. — Vol. 62. Issue 3. — P. 489-497
  • 3 Demyanenko E.G., Rorov I.P. Investigation of the flanging process for the parts with high conical angles // Materials Science Forum. — 2019. — Vol. 946 MSF. — P. 719-725
  • 4 Demyanenko E.G., Kosolapova A.Y. Development of a mathematical model of operation forming with discounting assumption about the flat-deformed state // Journal of Physics: Conference Series. — 2019. — Vol. 1368. Issue 4.
  • 5 Demyanenko E.G., Epifanov A. N. , Popov I.P. Simulation of plastic forming process by variation of geometric parameters // Journal of Physics: Conference Series. — 2019. — Vol. 1368. Issue 4.
2018
  • 1 Demyanenko E.G., Popov I.P. Investigation of application of flanging process for obtaining convex parts // IOP Conference Series: Earth and Environmental Science. — 2018. — Vol. 194. Issue 6.
2017
  • 1 Demyanenko E.G., Popov I.P., Menshikov V.S. Research of the process of axisymmetric forming of thin-walled flat blanks into the conical parts with minimal thickness variation // IOP Conference Series: Materials Science and Engineering. — 2017. — Vol. 177. Issue 1.
  • 2 Demyanenko E.G., Popov I.P., Abroyan A.U. Research of forming of thin-walled axisymmetric cone-shaped parts // IOP Conference Series: Earth and Environmental Science. — 2017. — Vol. 87. Issue 8.
  • 3 Demyanenko E.G., Popov I.P., Epifanov A.N. Simulation of plastic forming process of shells with minimal thickness fluctuations // Procedia Engineering. — 2017. — Vol. 201. — P. 489-494
  • 4 Dem'yanenko E.G., Epifanov A.N., Lygin Z.D. Проектирование штампованной оснастки для способа отбортовки из конической заготовки эластичной средой // Известия Самарского научного центра РАН 2017. — Vol. 19. № 6. — P. 30-35
  • 5 Demyanenko E.G., Popov I.P. Study of Al-Cu-Mn and Al-Mg-Si alloys thin sheets weldability // Key Engineering Materials. — 2017. — Vol. 746 KEM. — P. 22-28
  • 6 Demyanenko E.G., Popov I.P. Investigation of forming method based on flanging process // IOP Conference Series: Earth and Environmental Science. — 2017. — Vol. 87. Issue 8.
2016
  • 1 Demyanenko E., Popov I.P. Directional thickness alteration of a thin-walled ring blank using flanging and forming for the purpose of receiving conical part // -. — 2016. — Vol. 684. — P. 253-262
  • 2 Demyanenko E.G., Popov I.P. Study of thermal resistance and mechanical properties of thin sheets of low-alloyed aluminum Al-Cu-Mn and Al-Mg-Si alloys // International Conference on Industrial Engineering, 2016. — 2016. — Vol. 870. — P. 95-100
  • 3 Dem’yanenko E.G., Popov I.P. Study of thin-walled parts shaping process based on flanging and embossing // Russian Aeronautics 2016. — Vol. 59. Issue 2. — P. 277-282
  • 4 Demyanenko E.G., Popov I.P. The effect of the additional processing during the crystallization of a melt of the AD0 aluminum alloy on the size of grains // International Conference on Industrial Engineering, 2016. — 2016. — Vol. 870. — P. 614-619
2015
  • 1 Grechnikov F.V., Dem’yanenko E.G., Popov I.P. Development of the manufacturing process of aluminum alloys with high strength and conductance // Russian journal of non-ferrous metals 2015. — Vol. 56. Issue 1. — P. 15-19
2014
  • 1 Dem'yanenko E.G. A technique of shaping the barrel-type parts // Russian Aeronautics 2014. — Vol. 57. Issue 2. — P. 204-211
2012
  • 1 Dem'Yanenko E.G., Popov I.P. Limits of flanging process feasibility to create thin-wall conical shells // Russian Aeronautics 2012. — Vol. 55. Issue 4. — P. 408-412